Losi LOSA0887 Manual Manuel d'utilisateur

Take your time and pay close attention to detail. Keep this manual for future reference.Carefully read through all instructions to

2093132291434353633737BAG B7Figure 15Figure 16Step 3. Insert two 4-40 x 7/8" cap-head screws (33) — one on eachside — through the second hole out

93234381739404542444647Figure 178BAG B (Continued)Figure 18Step 8. Insert a front axle (39) into each of the front spindles [right(40), left (41)] as

1074238BAG B (Continued)9Figure 20Step 15. Attach the right spindle and carrier assembly to a front sus-pension arm (48) as shown in Figure 20. Note t

38105632424953211432 54 5510BAG B (Continued)Figure 22Step 22. Thread a long plastic rod end (54) onto each end of a 2-1/4"turnbuckle (55). Tig

1011840 55 54BAG B (Continued)11Figure 24Figure 25Step 25. Thread a long plastic rod end (54) onto each end of a 2-1/4"turnbuckle (55). Tighten

59585723BAG C12Figure 26Figure 28Figure 29Step 1. Insert a 4-40 mini locknut (7) into the hex area of the diff nutcarrier (57). The thread-locking por

65646160GREASE636564BAG C (Continued)13Figure 30Figure 31Figure 32Step 7. Insert a 5mm x 8mm bearing (63) into the center of the diff gear(64).Step 8.

BAG C (Continued)14Figure 33Figure 33Figure 34Step 15. Locate the smallest of the Allen wrenches (59) and place itthrough the slot in the outdrive/dif

15Figure 35BAG C (Continued)Figure 35Figure 36Step 24. Press the 1/16" x 5/16" pin (74) into the small hole in theslipper shaft (73) so that

83847573648180BAG C (Continued)16Figure 38Step 32. Use the short, 4-40 thread-cutting screw included in thewrench bag to pre-tap the three holes noted

WELCOME XXX-NT SPORT OWNER!Thank you for choosing the Team Losi XXX-NT Sport as your vehicle to enjoy the exciting world of nitro powered all-terrain

828887868583BAG C (Continued)17Figure 41Figure 42Step 38. Insert the brake shaft (77) through the 3/16" x 3/8" bearing(80) in the left gearb

BAG C (Continued)18Figure 43Step 44. Slide the slipper backing plate (89) over the slipper shaft (73), aligning the flat sections on the slipper shaft

BAG C (Continued)19Figure 44Step 56. Place one of the brake caliper plates (99) over the two brakesleeves (97).Step 57. Slide the brake rotor (100) on

1029610195951019610377Figure 46Figure 47Step 61. Place a 1/4" x .020 washer (96) over each of the two 4-40 x 5/8" set screws (27).Step 62. W

17882019291041920104105BAG C (Continued)21Figure 48Step 65. Thread a 8-32 x 1/8" set screw (105) into each of the two holesin the front of the re

10811110617106107BAG D22Figure 51Figure 52Figure 52 Attach the dogbones (107) to the plastic universal yokes (106) bylining up the slot on the dogbone

1121141171093856115114116BAG D (Continued)23Figure 55Figure 54Figure 55Figure 54Step 5. Thread a 3/8" ball stud (38) into the outer hole in the

333835123BAG D (Continued)24Step 17. Insert two 4-40 x 7/8" cap-head screws (33), one on eachside, through the outer holes in the top of the rea

124 54BAG D (Continued)25Step 19. Place the rear shock tower (123) over the rear of the gearboxassembly (82)(83) so that the top holes line up. Place

26BAG D (Continued)Step 23. Slide the battery box (125) into place on the back of thechassis (19). The top flange of the battery box (125) should fit

iiRADIO/ELECTRICALRefer to the included JR Propo XR2i owners manual for specific technical information.HARDWARE IDENTIFICATIONWhen in question, use

BAG E27Figure 62Step 1. Place one shock O-ring (126) into the cartridge body (127),making sure that the O-ring (126) sits flat on the bottom of the ca

BAG E (Continued)28Step 6. Using needle nose pliers, or small vise grips, grasp the frontshock shaft (130) between the grooves and thread a shock end

BAG E (Continued)29Step 13. Match the short, front shock bodies (137) to the short, frontshafts (130), and the long, rear shock bodies (138) to the lo

30BAG E (Continued)Step 22. Make sure that the dogbones are in the outdrives (47) beforecontinuing.Step 23. Attach the bottom of a rear shock (the lon

145146148150144146147115114149150114BAG F31Step 1. Inspect the inside of the tires [front (144), rear (145)] for any excess material. If present, trim

ENGINE INSTALLATION3 2Figure 73Figure 71Step 1. Thread a clutch pin/screw (151) into each of the small holes inthe flywheel (152) and tighten with

ENGINE INSTALLATION (Continued)33Step 5. Hook the two ends of the clutch spring (156) together to forma loop as shown. Stretch the looped spring (156)

ENGINE INSTALLATION (Continued)3 4Step 12. Place a ball stud washer (9) over the four 4-40 x 1/2" cap-headscrews (31). Insert a 4-40 x 1/2"

3 5ENGINE INSTALLATION (Continued)Step 14. Install the carburetor to the engine as per the instructionssupplied with the engine. The carburetor thro

3111283711186213465BAG A1Figure 1Figure 2Step 1. Place the servo saver bottom (1) over the servo saver post (2)and slide the servo saver bottom all th

1715131614181419201421BAG A (Continued)2Figure 4Step 8. Insert a 3/32" x 3/16" plastic bushing (13) into the two large,angled holes in the b

Ball stud washer required for some servos79112215.00˚Figure 7BAG A (Continued)Step 14. Using Table 7C, determine which servo arm (22) is requiredf

2627242317252419BAG A (Continued)Figure 8Step 17. Use the tables in Figure 7B and 7C (on the previous page) todetermine how the servo mounting posts (

112228292823173029BAG A (Continued)Figure 11Step 22. Attach one end of the rod to the ball stud (11) in the servoarm (22) and the other to the ball st

BAG A (Continued)Figure 14Step 26. Place the chassis brace (29) on top of the chassis (19). Pay particular attention to the servo posts (24). The pins